D Road test should be carried out with 2 persons, a driver and a tester, on a level road. D Insert each cap portion fully when installing high-tension cords. Wheel Bearing Inspection 1 Check front wheel bearing for wear, damage, abnormal noise or rattles. Accordingly, when any internal engine parts are serviced, care and cleanliness are important. These general precautions apply to many of the service procedures described in this manual, and they will not necessarily be repeated with each procedure to which they apply. If not, align two marks by turning camshaft but be careful not to turn it more than its allowable turning range which is described on previous page. This allows you to avoid paying out the often excessive costs for a bound copy of the same information.
For the details, refer to description on Freeze frame data. On mat- ing surface of cylinder block, four alphabets are stamped as shown in figure. Should this valve be clogged, engine would tend to overheat. Condition Possible Cause Referring Item Hard Starting. Valve spring retainer Apply sealant to mating surface of 3.
D Ease out piston pin circlips 1 , as shown. Muffler mounting : Do not reuse 5. The fact is that no car is indestructible, and big problems often start out as smaller problems that get ignored. Speedometer cable disconnected or broken. Is it in good condition? Check Output Shaft Speed Sensor for Resistance. Hand tighten only at this time. Then the signal causes the door lock controller to lock and unlock the door.
Intermittent trouble Go to Step 3. Failure to follow cautions may adversely affect electronic control system. Intermittent trouble or Clean rotor teeth or See Fig. D Using a cylinder gauge, measure cylinder bore in thrust and axial directions at two positions as shown in figure. If done so, it may cause adverse effect to catalyst. Condition Possible Cause Referring Item Hard Starting. Measure crank pin for out-of-round or taper with a micrometer.
D Be sure to oil crankshaft journals, journal bearings, thrust bearings, crankpins, connecting rod bearings, pistons, pis- ton rings and cylinder bores. Intermittent trouble Go to Step 3. Make sure that sensor heater is at correct temperature. If no description or specifi- cation is provided, refer to the following tightening torque chart for the applicable torque for each fastener. The contact points of this sensor for P and N ranges are also connected with the starting motor circuit. D Be sure to replace gaskets and O-rings as well as worn or damaged parts. After adjustment, tighten lock nut to specified torque while hold- ing adjusting screw stationary, and then make sure again that valve lash is within specification.
These manuals contain photos and diagrams as used by professional mechanics and repair shops to troubleshoot and fix your engine. Japanese automobile manufacturing has a strong reputation. If malfunction is found, replace. Flywheel bolt 3 Remove crankshaft pulley, timing belt and crankshaft timing pulley. D Never connect any tester voltmeter, ohmmeter, or whatever to electronic control unit when its coupler is disconnected. Tightening Torque a : 11 N m 1. Check each part which is suspected to be the cause.
D Road test should be carried out with 2 persons, a driver and a tester on a level road. After installing oil seal housing, gasket edges might bulge out; if so, cut them off to make them flush with cylinder block and oil seal housing. Does speedometer indicate vehicle speed? Seal : Tightening Torque 4. Is it in good condition? Piston pin guide for installation Oil pressure gauge 5. Outer rotor: Apply thin coat of engine oil. If desired section, item or description is not found in it, try next one in the list and do the same one by one till what is being searched is found.
D Check if cushion 2 is scored or damaged. Diagnostic information can be checked and erased by using a scan tool 2 Driving Cycle Detection Logic Refer to Section 6 or 6-1 for details. That is, install number 2 stamped piston to cylinder which is identified with number 2 and a number 1 piston to cylin- der with number 1. The filtered oil flows into two paths in cylinder block. Speedometer cable disconnected or broken.
A cylindrical cast against the cylinder wall as the piston travels its path. Tighten housing bolts to specification. Oil pan: Apply sealant 99000-31150 to oil pan mating surface. If clearance exceeds its limit, use a new standard size bearing and remeasure clearance. Does speedometer indicate vehicle speed? If there is no vacuum, check for clogged valve. As it takes time for valves to settle in place, operating engine within half an hour after their installation may cause interference to occur between valves and piston.
For this purpose, use of such an inspection form will facilitate collecting information to the point required for proper analysis and diagnosis. Immobilizer indicator lamp Vehicle not equipped with monitor coupler For G13B engine. Please press the like button if it was helpful! If malfunction is found, replace. Never replace cylinder head without replacing housings. D When connecting connectors, also hold connectors and put them together until they lock securely a click is heard. Check each terminal visually for poor contact possibly caused Check contact tension by inserting and removing just by dirt, corrosion, rust, entry of foreign object, etc. After installing plate, check to be sure that gears turn smoothly by hand.